What are your ideas about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging job. If the old tub is easily obtainable, the project can relocate quickly; if you need to open a wall to remove the old tub and place the new bath tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the work and also are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed job, it is better to take into consideration utilizing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This write-up will help you set up a new bathtub in your washroom if you have actually already bought a brand-new tub and don't require to change the arrangement of your previous water system pipes.
Your devices and also product checklist need to comprise the following:
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to stop stress on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath should now be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is separate the water system. After doing so, switch on the taps to drain any type of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited access that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning throughout this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing compound.
Before going on to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of the two wood boards under its feet, position the bath tub in the required placement. The wood boards are valuable in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bathtub up until the level checks out degree.
To install taps, fit the bottom of the furthest adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water as well as inspect all joints and brand-new pipework for leaks and also tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the normal outlet for leakages.
Finally, repair the bath paneling as described in the supplier's user's manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has been utilized at the very least once as this will certainly settle it right into its final setting.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in area between the tap and the sink. Secure the tap in place with the producer given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The former kind needs to be linked to the tap ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, causing complications with wetness and feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed our topic on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for taking the time to read our blog. Sharing is caring. You won't know, you may be helping someone out. I truly appreciate reading our article about How to Install a Bathtub.
Visit The Following Page